Ram Air

Sportrider Magazine
December 1999

mag_sportrider,craig.gif (162625 bytes)

By Kent Kunitsugo

 Part Deux

Does it work?

IT'S CRUNCHTIME
, ladies and gentlemen. After gathering hard information on the exact amount of airbox pressure present at speed in various ram-air-equipped sportbikes, via Pi Research's System 3 data-acquisition system, the time has come to strap these bikes to the dyno and see how much additional power is really available. This is where Sport Rider finally answers the question of whether all this ram-air horsepower hype is a measurable performance increase or nothing more than advertising smoke and mirrors.

We took the ram air data, seven current sportbikes and the Pi data-acquisition system to Two Brothers Racing in Santa Ana, California, where proprietor Craig Erion would run the bikes on his Factory Pro EC997a Eddy Current dyno. The Eddy Current dyno was chosen because of its ability to hold a steady rpm; this made it a lot easier to set the correct airbox pressure, compared with the common Dynojet dynos that can only make a complete run through the rpm range. With the Pi System 3, measuring the airbox pressure at speed for the first segment of our ram air test was a simple task. And its sophisticated software permits the user to view the pressure data in real time using a laptop computer. This gave us the chance to set the pressure on the dyno to the same parameters derived from the previous top-speed test.

Our biggest obstacle to completing this experiment was figuring out a way to force enough air into each of the airboxes to simulate the pressure encountered at speed while running on a dynamometer. There is an incredible amount of wind energy a 150 mph. If you've ever popped up out of the bubble while braking for Turn One at Daytona, or even stuck your hand out of a car's window while traveling faster than 130 mph, you know what we mean. We required more than a fan setup that ran up huge cfm (cubic feet per minute) numbers. It would need to supply that volume at pressures above ambient, requiring a large, high-horsepower fan and the necessary ducting - not something readily obtained without spending huge amounts of money, nor easily built and mounted in the limited space and time we had available. Several fan  options were tried but none could provide the amount of pressure we needed.

The setup we finally used may seem a bit unorthodox but it definitely gave us the necessary amount of wind energy and pressure. A pair of huge 185 cfm portable air compressors normally used with jackhammers were employed, and the requisite three-quarter-inch hoses directed the airflow. For the smaller bikes, we only needed to direct one compressor hose at a distance from the ram-air inlet to get the necessary pressure. The larger bikes, however, required us to use both hoses and, in some cases, seal up one side of the ram-air inlet while force-feeding the other. It should be noted that Eddy Current dynos typically give horsepower readings 15-20 percent lower than the more common Dynojet dyno readings. We started each run at 7000 rpm (both with and without ram-air assist), since we figured all of our top-speed data was gathered using full throttle and anything less than 7000 rpm in top gear would offer inconsequential ram-air pressure/data. Also, although many will argue that using air compressors brings up the issues of heat (compressing air raises its temperature) and moisture (compressing air also condenses moisture in that portion of air), these graphs are basically relative in nature and the increase in air temperature and amount of moisture condensation present were negligible.

Unfortunately, two bikes that were present during the top-speed data sessions had to be returned before we could begin the dyno sessions. Both the Kawasaki ZX-7R and ZX-9R are missing from these tests. However, we did manage to procure a Honda CBR600F4 and Kawasaki ZX-6R to take their places.

On each of the dyno graphs, the bold lines represent ram-air-assisted readings - solid for horsepower, dotted lines for torque. As we stated in "Ram Air Test: Part One" in our October issue, the results will definitely surprise you.

YAMAHA YZF-R6

Here is obvious proof that ram air works on smaller-displacement engines. Ram air helps the YZF hold its peak power higher and longer (12,000-14,000 rpm), and the torque curve is higher and flatter as well. This isn't just an incremental increase on top, either. We're talking about an average difference of five horsepower through the midrange and a far more usable power spread. The ram-air assisted reading would probably be higher at 13,000 rpm, but we were unable to generate the required airbox pressure on that particular run at that point. To give a relative reference, without ram air the Yamaha registered -11 millibars. Again, remember the lower peak horsepower reading of 84.4 is due to the Eddy Current dyno. (see True HP Scale explanation)

SUZUKI TLIOOOR

It was difficult to determine what the average peak pressure was in the Suzuki TL-R's airbox (check out its graph in "Ram Air: Part One," October '99), so we decided to stick with 12mb. Although we were skeptical at first, it's fairly apparent ram air works on V-twins, too. The horsepower and torque curves are well above their non-ram-air counterparts, with a seven horsepower bump at 10,000 rpm. It should be noted that the sealing on the Suzuki ram-air components (specifically where the ducts route into the airbox) is less than satisfactory. We encountered substantial leakage and estimate that peak pressure might be higher if the connection points had a more effective seal. The non-ram-aired TL-R registered -19mb for relative comparison purposes.

SUZUKI GSX-R750

The GSX-R750 is another case where ram air helps the engine hold its peak power higher and longer. The dip at 10,000 rpm on the ram-air graph is the result of a pressure glitch. We had a problem getting the correct Millibar setting at that rpm, in addition to a persistent exhaust gasket leak. Note the power peak builds earlier and carries much farther compared with the non-ram-air graph. The GSX-R also suffered from leakage around the airbox/ram-air ducts. Again, overall peak pressure could be higher if the componentry had a better seal. Without ram air, the GSX-R drained the airbox to the tune of -11mb.

RAM AIR HONDA CBR1100XX

Well, what would you rather have - 115 horsepower or 122 horsepower? The CBR-XX obviously reacts well to ram-air induction. The horsepower and torque curves literally mimic the non-ram-air graphs, only with a five to seven horse power increase and three to five additional foot-pounds of torque. It should be noted the Honda XX's ram-air system is one of the most efficient on the market, showing immediate power gains well before the 7000-rpm starting mark and posting high-pressure readings during our top-speed test. For comparative purposes, the CBR-XX's pressure reading without ram-air assist at full-throttle/top rpm was -8mb

SUZUKI GSX1300R HAYABUSA

Even though the Hayabusa ram-air-assisted read posted median pressure numbers during our top-speed and didn't build pressure beyond ambient until 145 mph, it's apparent that any internal combustion motor benefits from ram-air induction. The reason the power curve is tailing off a bit around 9500 rpm is because the Suzuki's mondo engine was basically beginning to require more air than we could feed it at that point. It was the only motorcycle we ram-air-dynoed that left both compressors gasping for breath. And again, the Hayabusa suffered from leakage around the airbox/ram-air duct junctions, which possibly prevented it from posting higher numbers.

KAWASAKI ZX-6R

After witnessing the high pressure readings garnered by both Kawasakis during our top-speed tests in the first session, we were anxious to see what another ZX-R could do on the dyno. Unfortunately, we ran into a problem. As the revs started to climb beyond 10,000 rpm, we couldn't get the Kawasaki to run cleanly.It was obvious the float-bowl vents weren't getting the same airstream pressure as the airbox during our dyno runs. Without ram air, the ZX-6R ran perfectly and posted excellent power numbers. No matter what we tried, we couldn't get our simulated pressurization to work with the Kawasaki's ram-air system properly. It was frustrating. If we would have had more time to fabricate ducting that enshrouded the ram-air inlets, we're confident our ram-air simulation would've worked. Still, the ZX-6R shows the initial signs of definite power gains up to 10,000 rpm. And judging by the excellent graphs drawn from our top-speed tests of the 7R and 9R, it's a sure bet the ZX-6R would have set the pace as far as showcasing the benefits of ram-air induction.

Copyright SPORT RIDER / DECEMBER 1999


True Rear Wheel Horsepower® Factory EC997a Eddy Current Dynamometer

 

Contact Factory Pro
M-F, 9am - 6pm, Pacific time, -7 or -8 GMT

800 869-0497
 USA and Canada

415 883-5620

fax 415 492-8803

parts information
 info@factorypro.com

EC997 dynamometer information
info@factorypro.com

Product Support /Tech SECTION
click here

Mailing / Shipping address:
Factory Pro
179 Paul Drive
San Rafael, CA
USA

And most importantly
Restart back at the HOME page and click on the red box in the top left to find the bike that you want parts for...
HOME

 



Absolutely NO carb kits or parts sold in California.

New and improved Suzuki Teka SFI 2
with new TPS display and "MMT" Memory Module Tuner

Finally - Quick, tuning with no expensive "add-on boxes"
Suzuki cruisers and sportbikes

Please click here for more info

Contact Factory Pro
M-F, 9am - 5pm, Pacific time, -7 or -8 GMT

800 869-0497
 USA and Canada

415 883-5620

parts information
 info@factorypro.com

EC997 dynamometer information
info@factorypro.com

Product Support /Tech SECTION
click here

 

Mailing / Shipping address:

Factory Pro
101c Roblar Drive
Novato, CA
USA

And most importantly
Restart back at the HOME page and click on the red box in the top left to find the bike that you want parts for...
restart at HOME page

 

This Tuning Site has been visited by
  
people.
www.digits.com - the oldest counting service on the web
          

 

 

 

LINKS
People ask me how I select the below links - as they aren't all mc related.
The below links are people and companies that are consistently impressive with their continual uniqueness and dedication to providing traditionally valued, quality products and services.
Marc
EFI and Carb Tuning by Wheelsmith Racing
The Harringtons own American Flyers, one of the most established flight training facilities in the USA - 8 locations -
 800-362-0808

Flight Training - train with AMA race winner Todd Harrington.
The Rich Oliver Mystery School will help you discover your hidden inner strength. 
It will challenge you. It will teach you a new way of thinking, and a new way of riding. You can take your riding to an exciting new level!  

We use a variety of proven drills and training techniques. 
Practicing these techniques with our Yamaha dirt track trainers will enhance your abilities both on the track or the street.  

It doesn't matter what you ride or race, the Rich Oliver Mystery School improves everyone's skill level and mindset!
Make your next tour Unforgettable,  Affordable and Exotic.
Superbike Tours Thailand - See you there.

Geoff@superbiketoursthailand.com
Supwebike Tours Thailand

Vintage Flying Special!

Book a sightseeing flight over the Wine Country or a Kamikaze aerobatic flight or a biplane flight over Infineon Raceway, the Golden Gate Bridge and the San Francisco Bay for one or two during the spring and get a free souvenir t shirt!
(NEW!  Ask about the P-40 flights!)

707 938 2444

Just say that you saw this on the Factory Pro website!
Marc

Northern California's most unforgettable flying experience.  No experience required.  Open weekends!

Artisan Crafted Fine Cheeses - Since 1865       

Specializing in Handmade Brie & Camembert

Marin French Cheese Co., also known as The Cheese Factory and Rouge et Noir is not just the oldest cheese manufacturer in the country, but a vacationers and day trippers destination as well as a unique part of American History. Located north of San Francisco, east of Napa County, west of Pt. Reyes and Olema and south of Sonoma County, Marin French has produced hand crafted Artisan soft ripened cheese since 1865. Rouge et Noir cheeses are similar to French and European varieties but reflect the characteristics of Northern California, producing it's own regional style.
The extension of the laboratory for engines of the Swiss Federal Institute of Technology was completed in about 1935. Its architect was Rudolf Otto Salvisberg (1882-1940). He had a successful career in Berlin but returned to Switzerland after the advent of the Nazis. His architectural style was somewhat similar to that of Erich Mendelsohn. The staircase of the laboratory is in normal use but well preserved.
Edited to the tunes of Chemical Residue by Herbie Hancock.